Other Adhesives

• Adhesive will harden fully
• Approx. 30 seconds s after all liquid has been applied

• Appearance
• Appearance Off-white pliable putty
• Beige trowelable mastic
• Khaki homogenous non sag paste
• Viscous white liquid

• Appearance
• Black, homogeneous paste
• Clear liquid
• Clear, colourless viscous liquid
• Yellow-amber Liquid

• Appearance and Type
• Synthetic Rubber spray

• Appearance:
• White Paste

• Appearence
• Clear, colourless viscous liquid

• Apperance
• Clear, almost colourless liquid

• Application
• All purpose
• Automotive glass replacement
• Building and DIY industry
• Carpet and Vinyl
• Carpet or vinyl tiles
• Construction and almost every application imaginable
• General purpose
• Ideal for home, school or office usage:
• Ideal for household repairs, DIY tasks and handicrafts
• Ideal for industrial, home, school or office usage
• Industrial
• Instant repair
• Multi-purpose
• Multi-Purpose
• Rear view mirror, glass and DIY

• Application
• Industrial interior and exterior use

• Application temperature
• Application temperature 15°C to 30°C

• Application temperature range
• Min. -5°C to max. +30°C

• Application temperature range
• Min. 0°C to max. 50°C

• Application Temperature:
• +5 °C to +35 °C

• Applications
• Surfaces exposed to damp, wet or underwater conditions.

• Cold Resistance
• Retains elasticity down to –30°C

• Colour
• Cream
• Dries clear

• Colour – Prior to curing
• White Outer / Khaki Inner

• Colour – Prior to mixing
• Blue Outer / White Inner
• Grey Outer / Black Inner

• Colour – Upon curing
• Off White
• Steel grey
• White

• Continuous temperature Rating
• 75°C.

• Coverage
• Approx. 2.8m2 at 1mm thickness

• Coverage/L
• ±4m²/L depending on the porosity of the substrate and thickness of the adhesive film

• Density
• Approx. 0.85 (g/cm3 @ 20°C)
• Approx. 1.38 g/cm3

• Density
• Approx. 0.85(g/cm3 @ 20°C)
• Density (g/cm³) 1.6
• Density Approximately 1.36g/cm³

• Density Approx
• Approx. 1.03 g/cm3

• Drying Time
• 2 - 5 minutes at room temperature

• ensile strength (MPa)
• ≥8.0

• Final cure
• 60Minutes

• Hardens in
• 10 Mins

• Hardens in
• 10 Mins

• Heat Resistance
• Up to 50°C

• Heat Resistance
• Softening occurs at elevated temperatures above 45°C

• Heat resistant
• Can withstand up to 149°C.

• Heat resistant
• Can withstand up to 149°C.

• Minimum Application Temperature
• 4°C

• pH:
• ~6-7

• Service temperature range
• Min. -5°C to max. +50°C

• Service temperature range
• Min. -10°C to max. 70°C

• Setting time
• Approx. 24 hours depending on substrate porosity and environmental conditions
• Sets in 007

• State
• Pasty liquid

• Tack free time:
• Approx. 5-10 min.

• Tack off time
• Approx. 30 - 45 minutes depending on site conditions: temperature, humidity and surfaces to be treated

• Temperature resistance up to 180°C
• Up to 180°C

• Temperature Resistance:
• -40 °C to +90 °C

• Type
• Ethyl Cyanoacrylate Adhesive
• Fibreglass reinforced polymer compound
• Hybrid polymer
• Liquid and powder
• Methacrylate adhesive
• Nitrile rubber solution
• Polymer compound
• Re-usable
• Synthetic rubber-based
• Water-based synthetic ter-polymer

• Type
• Type Synthetic polymer base

• Type Water based
• Water based

• Water resistance
• Good
• Waterproof

• Water Resistance
• Good

• Water resistance
• Waterproof